PGT Construction Service Nationwide

Why Fort Lauderdale Homeowners Choose PGT Construction

We’re an independent PGT in Fort Lauderdale construction and repair provider serving the surrounding coastal neighborhoods. Our crews handle PGT WinGuard impact windows, PremierVue sliding doors, and Eze-Breeze panels daily, diagnosing and fixing the specific ways salt air, humidity, and tropical storm cycles wear these units down. This page is built from our local job files, not a manufacturer brochure, so you get the real story on repair costs, parts, and what actually holds up within a mile of the Intracoastal. Call (754) 354-7423 for a free estimate on any PGT repair or installation.

Call (754) 354-7423

Key Takeaways:

• PGT impact windows and doors are built for hurricane zones, but Fort Lauderdale’s salt air and humidity create specific failure points: rollers, compression seals, and interlocking meeting rails.
• We repair PGT units using factory-spec parts where fit and finish matter, and honest aftermarket options where the cost difference is substantial.
• We are an independent service provider, not an authorized PGT dealer, which means we recommend repair over replacement when the frame is sound.
• Impact window installation in Fort Lauderdale runs $8,000 – $25,000 depending on the opening count and the existing frame condition.

Why Trust Sawyer Remodel Fort Lauderdale for Your PGT Construction?

PGT builds windows and doors that are genuinely overbuilt for hurricane wind loads, but that doesn’t mean they never fail. What fails is everything around the glass: the rollers on a heavy WinGuard slider, the compression seals that flatten after a few storm seasons, the meeting rails on casement windows that get brittle in direct sun and salt spray. Our crews know these failure modes because PGT Construction in Lauderdale-by-the-Sea, FL and Fort Lauderdale keep handing them to us. Luca Romano runs every PGT job through the same standard: diagnose the actual cause, quote the repair in writing before any work starts, and never sell a full replacement when a sash, hinge, or weatherstrip fixes the problem. He trained at Los Angeles Trade-Technical College reading structural plans, spent weekends as a teenager gutting and rebuilding a craftsman bungalow in East LA, and has spent the years since applying that same hands-on standard to the tight older builds near Las Olas Boulevard. The work either holds up or it doesn’t. We make sure it does.

Common PGT Construction Problems We Fix in Fort Lauderdale

• Roller and track wear on PGT WinGuard sliding glass doors. A WinGuard slider with aluminum frame and impact glass can weigh 200 pounds or more. The rollers take that load every single cycle, and Fort Lauderdale’s sandy, salty air works its way into the track. What starts as a little resistance becomes binding, then the door derails entirely. We replace worn rollers with factory-spec or heavy-duty aftermarket units, clean and realign the track, and usually restore smooth operation in one visit.
• Damaged or brittle interlocking meeting rails on PGT casement and awning windows. The meeting rail is the vertical strip where two casement sashes lock together. On PGT WinGuard casements, that rail is engineered for structural wind load, but UV exposure and salt make the weatherstripping channels hairline-crack over time. Once the rail loses its flex, the windows don’t seal and the lock stops engaging. We replace the rail and weatherstripping rather than the whole window when the sash itself is square.
• Failed compression seals around PGT impact glass after hurricane wind cycles. Every named storm that brushes Fort Lauderdale flexes the frame and compresses the gasket material between glass and frame. After enough cycles, the seal flattens and stays flat. Water finds the gap. We see this most on west-facing windows that catch afternoon thunderstorms in the wet season. Fixing it means removing the sash, cleaning the channel, and installing new PGT-spec compression gasket, which restores the seal without touching the glass.
• Fogging between panes in PGT insulated glass units. This is a seal failure inside the glass unit, not a frame issue. Fort Lauderdale’s humidity makes it obvious fast: once the desiccant inside the spacer bar is saturated, condensation forms between the lites and stays there. The glass unit gets replaced, not the entire window. The frame, sash, and hardware all stay in place, which cuts the cost significantly versus a whole-new-window quote.
• Corrosion on PGT aluminum frame hardware near the coast. Homes east of Federal Highway get hammered by airborne salt. The hinges and locks on PGT WinGuard Aluminum frames are stainless or coated, but the screws and mounting brackets can corrode, especially older models installed before current coating standards. We swap these out during routine service so small locking issues don’t turn into seized hardware that needs drilling out.

PGT Parts & Our Repair-vs-Replace Approach

We use PGT factory-spec parts where the tolerances actually matter: hinges, locking mechanisms, and weatherstripping have to match the original fit or the unit never seals correctly again. For rollers and insulated glass units, we’ll recommend high-quality aftermarket options when the math makes sense. A PGT WinGuard slider that’s ten years old doesn’t need an OEM roller assembly priced like a car payment; it needs a set of rollers that carry the weight and roll true. If the frame is square, the glass is clear, and the hardware is replaceable, we repair. If the frame is twisted from hurricane racking or corroded through on the bottom rail, no new roller or gasket will fix it, and replacement is the honest call. Call (754) 354-7423 and we’ll tell you which side of that line your window or door sits on.

Our PGT Service Process – Step by Step

1. 1
   Diagnosis. We inspect the unit as installed, not on a bench. That means checking the frame for racking, the track for wear, and the sash for square before we quote anything. We’ve got a repair estimate to you in writing, and that number is the number you approve.
2. 2
   Repair or installation. For window replacements and impact window installations, we pull the old unit, prep the opening, and check the surrounding flashing and sealant. Fort Lauderdale’s wind-driven rain finds every gap, so we re-flash the opening per Miami-Dade product approval standards before setting the new unit.
3. 3
   Test. Every repair gets a function test that matters for this climate: we cycle the window or door under load, check the compression seal with a water test on exterior-facing units, and confirm the locking points engage cleanly. If it doesn’t pass, we fix it before we leave.
4. 4
   Warranty. Every job is covered by our 365-Day Done Right Promise. If the repair doesn’t hold, we come back and make it right. That promise is in writing, on every job, and it covers our PGT work the same as anything else we do.

PGT Products We Service & Install in Fort Lauderdale

Our crews work on the full PGT lineup that shows up in coastal builds across Fort Lauderdale, including PGT repair in Plantation. That includes Winguard aluminum impact windows and doors, Winguard vinyl impact windows, PremierVue sliding glass doors, and Eze-Breeze sliding panels used on porches, lanais, and patio enclosures. We stock common PGT-spec weatherstripping, rollers, locking hardware, and compression seals in our local inventory so repairs don’t stall waiting on a parts truck. For glass replacements and full window replacement, we coordinate the order and schedule the install around your timeline, not ours.

We Also Service These Brands

PGT is a big part of our coastal repair work as a General Contractor, but it’s not the whole story. We install and service KraftMaid and Cambria in kitchen remodels, Silestone countertops, and Kohler fixtures in baths. Being multi-brand means we’re not pushing a single manufacturer’s product when a different one fits your project better.