Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Windows & Doors: The Fort Lauderdale Owner’s Guide
If you’ve got a Boral window or door that’s sticking, leaking, or simply worn out, we stock and install Boral-compatible parts across Fort Lauderdale, with most replacements running between $450 and $2,500 installed depending on the component. We typically carry common Boral hardware, weatherstripping, rollers, locks, and balances on our trucks, so a single visit usually solves the problem. You’ll know something’s off when a door scrapes the frame, a window won’t stay up, or you can feel air moving around the sash even when it’s closed.
Boral builds their windows and doors around aluminum and vinyl frame systems designed for coastal climates, which matters in Fort Lauderdale where salt air and humidity chew through lesser hardware fast. But even well-built units fail over time. The good news is most failures are mechanical, not structural: a worn roller, a broken balance, a tired weather seal. Those are the jobs we handle most often, and because we’ve been working on Boral products across South Florida for years, we know which parts interchange and which ones don’t.
Which Boral Models This Applies To
Boral’s window and door lineup spans a few distinct series, and the part you need depends on which one your home has. The most common lines we see in Fort Lauderdale homes are the Boral Builder Series, the Boral 220 Series, and the Boral 540 Series. The Builder Series uses standard 2-5/8″ frame depths and basic roller assemblies. The 540 Series steps up to heavier-duty hardware with stainless steel rollers and reinforced corner keys, built for impact-rated openings. If you’re replacing an older Boral unit with a newer part, the roller diameters often differ by 1/16″ to 1/8″, which doesn’t sound like much until the door binds or drops.
To identify your part, look for a white or silver sticker on the head jamb or the edge of the sash. It’ll have the series number and sometimes a manufacture date. No sticker? Measure the roller diameter and the length of the balance channel. That tells us what you need before we arrive. We always recommend OEM Boral parts when they’re available, because the tolerances line up exactly. For discontinued series, we source quality aftermarket equivalents that match the original specs, and we’ll tell you upfront which one we’re quoting. Sawyer Remodel Fort Lauderdale is an independent service provider, not affiliated with Boral, which means we’re free to source the right part for your home, not just whatever the factory still ships.
Styles & brands we work with
What It Costs for the Whole Job in Fort Lauderdale
Here’s what we charge in Fort Lauderdale, parts and labor included:
| Service | Typical Installed Price Range |
|---|---|
| Sliding door roller replacement (single panel) | $180 – $450 |
| Sliding door roller replacement (both panels) | $320 – $700 |
| Window balance replacement (single hung) | $150 – $350 |
| Window weatherstripping replacement (per window) | $80 – $220 |
| Door lock/handle set replacement | $160 – $420 |
| Hinged door hinge replacement (set of 3) | $140 – $380 |
| Window sash replacement (standard vinyl) | $350 – $1,100 |
| Sliding glass door panel replacement | $900 – $2,500 |
What drives the price is series compatibility and condition. A 540 Series roller set costs more than Builder Series because the hardware is heavier. If the frame is corroded or the track is bent, that adds labor time. Every quote is line-itemed: part cost, labor, and any trip or disposal fees stated separately. You get a written price before we touch a screwdriver, and that number doesn’t change at the invoice. The work carries our 365-Day Done Right Promise: if the part fails or the door starts acting up again within a year, we come back and make it right at no charge.
We also stock parts for KraftMaid cabinetry, Cambria countertops, and Silestone surfaces, so if your Boral replacement is part of a bigger repair, we can handle the full job in one visit.
See the difference
Before
After
Before
After
Before
AfterSigns Your Boral Windows & Doors Is Failing
- The door scrapes or drags when you open it. This is almost always a worn roller or a bent track. Fort Lauderdale’s sand and salt accelerate roller wear, especially on homes close to the beach.
- The window won’t stay open, or slams shut. The balance spring or block-and-tackle balance has given out. Once one side fails, the sash tilts and binds, which then damages the other side.
- You can feel air moving around a closed door or window. The weatherstripping has compressed or torn. In a humid climate like Fort Lauderdale’s, this also lets moisture into the wall cavity, which leads to bigger problems than a draft.
- The lock won’t throw or the handle feels loose. Boral lock sets use a multi-point mechanism on some series, and when one point fails, the whole assembly usually needs replacing rather than one small piece.
- The door is hard to lift into the track or keeps popping out. The adjustment screws on the rollers are stripped or the roller housing is cracked. This is a safety issue on heavy glass panels and worth fixing before the panel falls.
DIY or Call Us?
There’s a safe middle ground. You can clean the track with a brush and a vacuum, check for loose screws on the handle and lock plate, and visually inspect the weatherstripping. Those checks help a door work better for a little while. What you should not do is pull a sliding glass door panel out to swap a roller, or try to re-tension a window balance. Those parts carry the weight of heavy glass under spring force. One wrong move and you’re looking at a broken panel, a broken finger, or both. We get calls from homeowners who got halfway through a roller replacement and realized the adjustment screw was seized or the roller housing was a different diameter than the one they ordered online. At that point the door is off its track, the sun’s going down, and the security risk is real. Calling us before that point is cheaper. We carry the common Boral roller sizes, balances, and lock sets on the truck, so most repairs are done in a single visit.
FAQs
Frames typically last 20 to 30 years, but hardware like rollers, balances, and weatherstripping typically needs replacement every 5 to 10 years in Fort Lauderdale because of the salt air and humidity. Coastal homes a few blocks from the ocean are at the shorter end of that range. Call (754) 354-7423 and we’ll tell you if your specific part is worth replacing or if the whole unit has reached the point of diminishing returns.
Depending on the part, sometimes. Rollers can occasionally be cleaned and re-lubricated, and weatherstripping can sometimes be re-seated. But in most cases, by the time a Fort Lauderdale homeowner notices the symptom, the part is beyond a quick fix. We’ll tell you honestly if a repair makes sense, and you’ll get that recommendation before we order anything.
Most window balances, lock sets, and weatherstripping replacements are done in 60 to 90 minutes. Sliding door roller replacements on both panels typically take 2 to 3 hours, including track cleaning and realignment. We schedule a specific arrival time so you’re not waiting on a four-hour window.
We stock the most common Boral roller sizes, balances, weatherstripping, and lock sets for the Builder, 220, and 540 Series. If your part is uncommon or you have a discontinued series, we source it and schedule the install once it’s in hand. Either way, you’ll know before we start what the part costs and when we’ll have it.
If your Boral window or door is failing, call (754) 354-7423. We’ll ask what it’s doing, tell you what we think over the phone, and schedule a time that works for you. The estimate is free, the price is in writing before work starts, and the repair is backed by our 365-Day Done Right Promise. The work either holds up or it doesn’t – we make sure it does.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Fort Lauderdale at Sawyer Remodel Fort Lauderdale, serving Fort Lauderdale and nearby areas.
