Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Bathroom Remodeling: The Fort Lauderdale Owner’s Guide
If you own a home in Fort Lauderdale with a Boral bathroom product that’s cracked, leaking, or failing, a full bathroom remodel typically runs $9,000 to $28,000 installed, depending on size and what’s behind the walls. We stock Boral-compatible trim, panels, and waterproofing components on the truck, and we can usually have a technician out to look at your bathroom within 24 to 48 hours of your call. Most owners discover the problem the same way: a hairline crack near the shower base, a soft spot in the wall behind the vanity, or water staining on the ceiling below a second-floor bathroom. By that point, the failure has been happening quietly for months.
What we see most often in Fort Lauderdale is moisture intrusion around Boral panel edges where sealant has dried out in the salt air and constant humidity. Boral’s poly-ash trim and panels are tough, but no material shrugs off South Florida forever. The good news is that a Boral-specific remodel isn’t a mystery job. It’s about matching the right product line, pulling the failed sections correctly, and rebuilding the waterproof envelope so you’re not back here in three years. That’s where we come in.
Key Takeaways:
- Installed Boral bathroom remodels in Fort Lauderdale run $9,000 – $28,000.
- Boral trim and panels are repairable in sections, but full replacement is often cheaper long-term once water gets behind them.
- We carry Boral-compatible materials on the truck and source exact-match OEM parts same-week.
- Written price before work starts, photo updates before and after, live arrival tracking on every job.
Which Boral Models This Applies To
Boral doesn’t make a single “bathroom remodel” product, which is exactly where most Fort Lauderdale homeowners get confused. What they actually own is one of three things: Boral poly-ash trim boards used as baseboards and casing around a bathroom, Boral TruExterior siding panels that wrap an exterior bathroom wall, or Boral wall panels and wainscot inside a shower enclosure or wet zone. Each has a different failure mode and a different fix.
Here’s the compatibility gotcha most people miss: Boral poly-ash trim from the TruExterior line is not interchangeable with the older Boral Advantage trim profile. The reveal depth differs by roughly 3/16 of an inch, and if you mix them on the same wall, the joint will never sit flush no matter how much caulk you put in it. Before we touch anything, we check the backside of an existing piece for the stamped product code. TruExterior pieces carry a “TX” prefix. If the stamp is gone, we measure the reveal depth and match it against current Boral profile charts. In Fort Lauderdale, we’ve also seen a few homes with Boral’s discontinued Versetta Stone in shower surrounds, which requires a completely different fastening system and waterproofing approach than the trim lines.
For OEM versus aftermarket: Boral’s own poly-ash trim holds paint longer in Fort Lauderdale’s UV and salt exposure than most generic PVC trim, but PVC is what most competitors will quote you because it’s cheaper. We’ll quote both honestly, but if you’re in a moisture-heavy spot near the Intracoastal, stick with OEM Boral or a high-density poly-ash equivalent. The warranty math alone usually justifies it.
Styles & brands we work with
Signs Your Boral Bathroom Remodeling Is Failing
- Paint blistering or peeling at trim joints near the shower. This is moisture wicking into the poly-ash from behind. The material itself is fine; the waterproofing seal has failed. Left alone, the framing behind it starts to rot.
- A soft spot on the wall below the vanity or toilet. Water has been running down the inside face of the trim and pooling at the baseplate. By the time you feel it from the outside, the baseplate is usually compromised.
- Caulk lines that crack within weeks of re-caulking. If sealant won’t hold a bond, the substrate behind it is moving or wet. Caulk is a symptom, not a fix. We see this constantly in older Fort Lauderdale homes near Las Olas where framing shifts with seasonal humidity swings.
- Black staining or mildew along the bottom edge of exterior bathroom walls. Boral TruExterior panels should shed water. Staining means the drainage plane behind the panel is clogged or the panel was installed without the required air gap.
- Visible warping or “oil-canning” on flat panel surfaces. Poly-ash expands and contracts with heat. If a panel is fastened too tightly or without the required expansion gap, it will bow in the Fort Lauderdale sun. This is installation error, not material failure, and it’s fixable without full replacement if caught early.
Replacement Cost & What’s Included
In Fort Lauderdale, a Boral-specific bathroom remodel runs $9,000 to $28,000 installed. The spread is wide because the scope depends entirely on what’s failed and how far the water has traveled. A trim-only replacement around a standard 5×8 bathroom starts near the lower end. A full gut with waterproofing rebuild, new Boral panels, new shower base, and framing repair lands near the top.
Here’s what that range looks like in real terms for this market:
- Boral trim replacement (baseboards, casing, one wet wall): $900 – $2,800 per wall section, including removal, new OEM-matched poly-ash trim, waterproof flashing, and sealant.
- Boral TruExterior panel replacement on an exterior bathroom wall: $3,500 – $7,000 including panel removal, drainage plane inspection, new panel installation with correct expansion gaps.
- Full Boral bathroom remodel (shower surround, flooring, vanity area, waterproofing rebuild): $9,000 – $28,000 depending on square footage, tile selection, and whether framing repair is needed.
Every quote we write in Fort Lauderdale includes the part number for each Boral piece, the labor line item, and the waterproofing method. If the price changes once work starts, that means we found something we couldn’t see from the outside, and you’ll approve the line item before we touch it. That’s The Relay Standard, and it’s not optional on our jobs. The 365-Day Done Right Promise covers the work for a full year. If a Boral joint we installed fails in that window, we come back and fix it on our dime. The work either holds up or it doesn’t, and our guarantee makes sure it does.
DIY or Call Us?
If you’re replacing a single piece of Boral trim that’s cracked but dry, and the wall behind it is solid, you can do that with a miter saw, polyurethane adhesive, and stainless finish nails. That’s a Saturday job. But the moment you see staining, soft drywall, or water marks below a Boral panel, stop. What’s behind that trim in Fort Lauderdale is a framing cavity that’s been wet in 80% humidity, and that’s where mold starts. Cutting open a wet wall without knowing what’s behind it is how a $200 trim fix becomes a $4,000 framing repair.
We’d rather you call us before you cut. The estimate is free. Luca Romano has been in enough Fort Lauderdale bathrooms to know that the trim is rarely the whole story. Call (754) 354-7423 and we’ll send a background-checked, uniformed technician to look at it. You’ll get a live arrival time, not a four-hour window.
See the difference
Before
After
Before
After
Before
AfterCan Boral trim be repaired, or does it always need replacing?
Small cracks and chips in Boral poly-ash trim can be repaired with polyurethane adhesive and sanding, but only if the piece is dry and the wall behind it is sound. If the crack is at a joint where water has been getting in, replacement is the honest fix. Call (754) 354-7423 and we’ll tell you which one you’re dealing with, free.
How long does a Boral bathroom remodel take in Fort Lauderdale?
A trim-only replacement usually takes one to two days on site. A full bathroom remodel with waterproofing rebuild, Boral panel work, and tile typically runs two to three weeks from demo to final caulk. We give you a written schedule before we start, and we keep it.
Do you stock Boral parts, or do you have to order them?
We stock common Boral TruExterior trim profiles and sealants on the truck. Less common profiles and Versetta Stone components are special-ordered and usually arrive within a week in Fort Lauderdale. If you need an exact-match part number, we’ll confirm it from the existing piece before ordering.
Will the price change once work starts?
Only if we find hidden damage that wasn’t visible during the estimate, and you approve the additional line item in writing before we proceed. The number on your invoice is the number you approved. No change orders, no end-of-job surprises. That’s been our rule since 2005.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Fort Lauderdale at Sawyer Remodel Fort Lauderdale, serving Fort Lauderdale and nearby areas.
