Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Roofing: The Fort Lauderdale Owner’s Guide
If your Mr-Glass roof component has cracked, warped, or started letting water through, we stock Mr-Glass-compatible replacement parts and install them across Fort Lauderdale, typically for $400 to $1,800 depending on the part and roof access. Most owners first notice the problem after a heavy afternoon storm, when a water stain shows up on the ceiling or a piece of flashing pulls loose in the wind. The fix is usually straightforward once the right part is matched, and we can tell you over the phone whether we have it on the truck before we roll out.
Key Takeaways
- Mr-Glass parts are matched by panel profile and measurement, not just brand name. We confirm specs before ordering.
- Installed replacement in Fort Lauderdale runs $400 – $1,800 for most component-level fixes.
- We stock common Mr-Glass-compatible flashing, fasteners, and panel sections on the truck.
- Free estimates by phone at (754) 354-7423, and we never start work without a written price.
Which Mr-Glass Models This Applies To
Mr-Glass roofing products in Florida are most often the fiberglass-reinforced panel systems used on patio covers, carports, and lanai roofs, plus a smaller share of metal profile panels on sheds and screen enclosures. The part that matters first is the panel profile: Mr-Glass panels come in standard 26-inch and 36-inch coverage widths, with either a flat or corrugated profile, and a mismatch means the new panel won’t seat correctly against the old one. Before you call, check the underside of a panel for an embossed or printed series code, usually a letter followed by four digits. If you can’t find a label, measure the center-to-center distance between high ribs, because that measurement pins down the profile faster than any brand name will.
On the parts themselves, OEM Mr-Glass replacement sections are still available for most series made in the last decade. That said, we regularly install quality aftermarket equivalents from the same profile spec, and in Fort Lauderdale’s salt air and sun, a good aftermarket UV-stabilized panel often holds color longer than the original. The decision usually comes down to whether you need one small patch or a full blended reroof of a section. We walk through both numbers before any work starts.
Styles & brands we work with
Signs Your Mr-Glass Roofing Is Failing
- Water staining on the ceiling or beam below the panel. This usually means a fastener gasket has dried out and shrunk, letting rain wick down the screw shank. In Fort Lauderdale’s wet season, one failed gasket is all it takes.
- Panels lifting or flapping at the edges in wind. The aluminum edge trim or clamp strip has pulled loose, often because the original screws were overtightened and stripped their holes. This is a common failure on older patio covers we see from Coral Ridge to Victoria Park.
- Hairline cracks radiating from a screw hole. Thermal expansion does this. South Florida panels bake hot in the afternoon sun and shrink at night, and over years the repeated movement cracks the fiberglass around the fastener.
- Yellowing, clouding, or visible fiberglass fibers on the surface. The UV coating has worn away, and the panel is now losing strength. It still sheds water for a while, but it’s getting brittle and will crack under foot traffic or a branch.
- White chalky residue washing off the roof onto the patio below. That’s the gel coat breaking down. It’s mostly cosmetic at first, but it’s the same degradation that leads to leaks within a season or two.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a single Mr-Glass panel replacement in Fort Lauderdale, expect $400 to $800 installed, which covers the panel, matched fasteners with new gaskets, edge trim if needed, and labor for a standard one-story patio cover. If multiple panels or a larger section of the roof plane needs replacing, the job typically lands between $800 and $1,800 depending on square footage, roof pitch, and whether we need to pull and reset existing trim. A full reroof of a large lanai runs higher and gets quoted as its own project.
Every quote is written, line-by-line, and sent before work starts. The number on the invoice is the number you approved. If during the job we find additional fasteners that need replacing in the same section, we handle the small ones on the spot and let you know before adding cost. The work itself carries the 365-Day Done Right Promise: if anything we installed fails within a year, we come back and make it right at no charge. That’s in writing, not a handshake.
DIY or Call Us?
There are two things an owner can safely do before we arrive. First, photograph the failed area from below and text it to us, because a clear photo often tells us whether we’re replacing one panel or several. Second, identify the series code or measure the rib spacing, which we covered above. Both save a trip. What we don’t recommend is climbing onto a Mr-Glass panel. These panels get slick with algae and morning dew, and an aged panel can shatter under body weight without warning. Falls through patio roofs are a genuine mechanism of serious injury in South Florida, and no DIY panel change is worth that. If the repair requires walking the roof, let a licensed, insured crew do it with proper access and fall protection. Call (754) 354-7423 and we’ll send someone who does this work weekly, not once ever.
FAQs
Most Mr-Glass panels in Fort Lauderdale hold up 10 to 15 years before the UV coating breaks down enough to cause cracking or leaking. Homes closer to the ocean, especially east of Federal Highway, often lose a couple years off that because salt spray accelerates the surface wear. If your panels are past year 12 and showing chalky residue, replacement is usually cheaper than repeated patching.
A small crack can be sealed with the right polyurethane or fiberglass repair kit and hold for a season or two, but on a Fort Lauderdale patio cover exposed to daily sun and seasonal storms, a patch is a temporary fix, not a long-term answer. We’ll seal something small if the panel is still structurally sound, but we won’t promise it holds forever. Call (754) 354-7423 and we’ll tell you honestly whether it’s a seal job or a swap.
A single panel swap on a standard one-story patio cover runs one to two hours once we’re on-site, including removing old fasteners, resetting the new panel, and checking the surrounding trim. Larger sections take half a day. We give you a live arrival time and photo updates before and after, so you’re not sitting around guessing.
We keep common Mr-Glass-compatible panels, fasteners, gaskets, and edge trim on the truck for most standard profile widths. If your series needs an OEM panel we don’t stock, we order it and the wait is usually three to five business days in the Fort Lauderdale area. We also keep parts for KraftMaid, Cambria, and Silestone lines for other projects, so if you have a mixed material list, one call covers it. Call (754) 354-7423 for a free estimate and a straight answer on what’s in stock today.
Written by Luca Romano, Owner & Lead Contractor, Sawyer Remodel Fort Lauderdale at Sawyer Remodel Fort Lauderdale, serving Fort Lauderdale and nearby areas.
